Applying paint protection film is an easy way to make sure the exterior finish of your car has protection, especially when it comes to rock chips and bug stains.
Once you’ve applied the film, your car will get protection from scuffs and scratches that can cause your car to lose its shine and even rust. Paint protection films market size was estimated to be valued at around USD 440 million in 2020 and exhibits a 5.89% CAGR during the forecast period.
Check out these tips for installing paint protection film on your new vehicle.
Make Sure the Surface of Your Car is Clean
Make sure the surface of your car is clean before applying paint protection film. Wax and polish the car to remove any dirt or grime that could prevent the film from adhering properly. The film should be applied to a cool, dry surface. If the film is too hot, it will be difficult to work with. If the film is too cold, it will be more likely to crack.
The paint protection film is a clear urethane film that is applied to the painted surfaces of a car to protect them from chips, scratches, and weathering. The film is applied like a clear bra and is usually sold in rolls of various widths.
When applying paint protection film, it is important to avoid doing so in very hot weather. The heat can cause the film to warp and bubble, making it difficult to apply evenly. It is also important to clean the surface before applying the film, as any dirt or debris can cause the film to lift over time.
If the paint protection film is too cold, it will not stick to the paint and will eventually peel off. This is why it is important to apply the film when the temperature is warm so that it can adhere properly.
Don’t Apply Paint Protection Film on a Hot Surface
It’s important to keep your surface cool when applying paint protection film. Hot surfaces can cause the film to warp and bubbles to form. This can ruin the look of your film and make it more difficult to apply.
The only time you can use heat when applying the film is on a curved surface, as it can soften the film to bend to the shape of the curve. Make sure that you are doing the installation in a shaded or cool environment so that the adhesive will stick.
Start from Top to Bottom
To ensure your paint protection film is applied correctly, start at the top of the vehicle and work your way down. This will allow you to avoid any air bubbles or wrinkles that could occur if you start from the bottom. When applying the film, be sure to use a hard card or squeegee to work out any air bubbles.
Avoid using sharp objects when doing the application to prevent scratches or any damage on the surface of the film.
There are many benefits of auto detailing that can surely improve the condition of our car. For best results, have the film professionally installed.
Trim Off Any Excess Film
After you have ensured that the paint protection film is in place on the surface of your vehicle, you will need to trim the excess film. Be sure to take your time and be careful not to damage the paint underneath the film.
Use a sharp hobby knife or Exacto knife to get crisp and clean-cut. Score the film a few times before cutting to avoid the film from tearing. Make sure to cut precisely to avoid jagged edges.
When cutting around curves, be sure to use a scalpel for more intricate cuts.
After you have trimmed the excess film, use a heat gun or hair dryer to heat the edges of the film. This will help to seal the edge and prevent lifting.
Paint Protection Film After Care
Take note that regular washing and waxing of the vehicle are still necessary. The paint protection film will help protect the paint job, but washing and waxing will help extend the life of the film.
Avoid using harsh chemicals or abrasives when cleaning the vehicle. These can damage the film and/or the paint job.
You must be careful when parking in tight spaces. The film can be easily damaged by scratches from other vehicles or objects. Finally, enjoy your paint protection film and the peace of mind it brings!
If you do notice any lifting, peeling, or bubbling then get in touch with the company you purchased the film from as soon as possible as you may be covered by a warranty.
Bonus: Make Sure to Get High-Quality Materials
When it comes to buying a paint protection film, be sure to invest in high-quality materials. This will ensure that the film lasts longer and does a better job of protecting your paint. Also, be sure to follow the instructions when applying the film. This will help to avoid any air bubbles or wrinkles.
There are films sold for a certain make or type of car. This will ensure we have the right measurements and amount of the materials we need. Make sure to inquire if there is any warranty or insurance when getting the installation process done by a professional.
Get the Right Protection for Your Car
The best way to protect your car’s paint job is to apply paint protection film. This film will shield your paint from chips, scratches, and fading. The film is virtually invisible and will not alter the appearance of your car. There are many different brands and types of film available, so it is important to do your research to find the best option for your needs.
When applying the film, it is important to take your time and use a slow, steady hand. Once the film is applied, you can enjoy peace of mind knowing that your paint has protection from the elements.
You can find more great articles like this one on our website.
Hemant Kumar is a project manager at Tridindia with more than nine years of commendable experience in writing about LMS, translation, and IT. His unmatched talent and passion for digital marketing gave him the opportunity to work as a multi-tasking project manager at TridIndia’s sister company, Link Building Corp. Today, he contributes to the world by imparting knowledge on SEO, link building and internet marketing etc., that helps business owners grow their online business.
No responses yet